combining marks will have zero advance, but it results in zero-width
glyphs in subfonts. fall back to width so something meaningful is
rendered even if its not combined properly.
when clering smi enable bits in the legacy control/status register,
preserve the reserved bits. clear the RW1C bits.
linux code claims intel xhci controller needs a 1ms delay before
accessing any register after reset.
pcienable() puts a device in fully powered on state
and does some missing initialization that UEFI might
have skipped such as I/O and Memory requests being
disabled.
pcidisable() is ment to shutdown the device, but
currently just disables dma to prevent accidents.
on Samsung ATIV Smart PC Pro XE00T1C-A01CL, the EHCI handoff
causes the system to freeze in UEFI mode as soon as we assert
the os semaphore bit.
until a general solution is found, provide these parameters to
disable the handoff for now as it seems to otherwise work fine.
when a prefix is added with the onlink flag clear, packets
towards that prefix needs to be send to the default gateway
so we omit adding the interface route.
when the on-link flag gets changed to 1 later, we add the
interface route.
the on-link flag is sticky, so theres no way to clear it back
to zero except removing and re-adding the prefix.
automatic Referer headers were found to break downloads from
sourceforge.net, causing html pages to appear instead of tarballs.
if a website does need them, they can be added as needed via hget's -r
flag, or added to mothra.
reverts commits 67f536d20329 and 6d999c39a9f0
Once a second rebalance() is called on cpu0 to adjust priorities,
so cpu-bound processes won't lock others out. However it was only
adjusting processes which were running on cpu0. This was observed
to lead to livelock, eg when a higher-priority process spin-waits
for a lock held by a lower priority one.
syntax: reboot!bootfile[!method...]
this echos bootfile to /dev/reboot, causing bootfile kernel
to be started.
when method is given, we first connect to the filesystem and
set bootargs so that bootfile can be loaded from the target
network or local fileserver.
note, when no bootfile is given, this causes the kernel to
reboot to bios.
the end condition port < offset+n could never become
false when offset truncated to 32 bit signed port is
negative. change the condition variables to unsigned
int.
msr's are not byte addressible, so advance reads by
one instead of 8.
Xpipefd wants the pipe descriptor to be closed in turfredir(), so
it pushes the redirection, but this breaks Xpopredir after normal
redirection. so we shuffle the Xpipefd redir to the bottom of the
stack.
- plumbsel()
- remove debug prints
- use smalloc() to convert to bytes
- fix spurious -1 close of plumb fd
- snarfsel()
- fix rune buffer leak in open error case
Ori Bernstein wrote:
> I finally got around to taking another shot at this vt patch. This change
> gets rid of implicit snarfing, and instead makes selection the way you
> select text for snarfing or plumbing. Select, then use a menu entry.
>
> It would probably be nice to have double click to expand the selection,
> rio-style, along with plumbing implicitly taking the current word, but
> that can be a separate patch.
>
> This change also punts on scrolling for simplicity -- it clears the
> selection instead of trying to handle the cases where the selection
> goes offscreen.
little amendments:
- fix line selection (point min/max inversion)
- clear selection when switching linesel/blocksel
- move selection on scroll
the arp table is per interface, so it is possible to have the same
netwrok on multiple physical interfaces, tho with different source
ip address. one example would be a ethernet and a wlan interface.
the mac addresses on these mediums can differ (arp proxying taking
place).
so provide our source address on the interface we received the
request on.
the previous change used the ifcaddr; which is correct; but due to a
oversight in the kernel, had to match the ip of the arp entry.
source address will always work.
unless relay agent (gaddr) is specified, dhcp requests need to
taget a local ip address on the incoming interface or broadcast.
clients might have multiple ethernet interfaces, so we need to
check if any of the ether= attributes in ndb matches. this is
done by passing lookupip() the attribute name and a expected
value and if a match is found, set Info.indb = 1.
remove tohex(), use encodefmt instead. avoid dynamcic allocation.
include interface device in log messages.
sending multicast was broken when ipconfig assigned the 0
address for dhcp as they would wrongly classified as Runi.
this could happen when we do slaac and dhcp in parallel,
breaking the sending of router solicitations.
now handle the supported rates element properly, only
providing the intersecting set of rates that the bss
advertises and what the driver supports, putting the
basic rates first.
also avoid using usupported rates.
BurnZeZ → Found a bug in dc(1)
BurnZeZ → Everything breaks when you fill the stack
BurnZeZ → You have stkptr which crap expects to point to an available member in Blk *stack[STKSZ];
BurnZeZ → stkend = &stack[STKSZ];
BurnZeZ → stkptr is allowed to equal stkend
BurnZeZ → So crap that expects stkptr to be pointing to an available Blk ends up dereferencing past the end of the array
BurnZeZ → term% echo `{seq 1 100} f | dc
BurnZeZ → dc 628283: suicide: sys: trap: fault read addr=0xffffe0000040a618 pc=0x204b1c
nobody passes us the "RSD PTR " address when doing multiboot/kexec
on UEFI systems. so we search for it manually in the ACPI reserved
area as indicated in the e820 memory map.
launch wadfs after detecting main wad, exposing GENMIDI and music lumps
under /mnt/wad. /bin/dmus can then use them directly, and wadfs doesn't
need to be started manually.
"I sometimes find myself on either slow or data-capped network links where downloading images isn't ideal. Attached is a simple patch to mothra that changes the 'k' command to not only remove already-downloaded images from a page, but also toggle a state such that mothra won't attempt to download images on future visited sites until 'k' is toggled again. This also adds a '-k' flag to mothra which enables the flag at startup." --Jeremy O'Brien<neutral@fastmail.com> on 9fans
the target has to be encoded as a domain name (the individual
name components as separate labels followed by . (empty) label),
not as a literal string.
to disable compression, pass nil dictionary to pname().
- fix overwriting channel 10 with channel 9
- fix using channel volume instead of last volume when setting note
(fixes d_doom and others)
- remove useless state
we did not apply the special case to store 0xFFFF (-0)
in the checksum field when the checksum calculation
returned zero. we survived this for v4 as RFC768 states:
> If the computed checksum is zero, it is transmitted as
> all ones (the equivalent in one's complement arithmetic).
>
> An all zero transmitted checksum value means that the
> transmitter generated no checksum (for debuging or for
> higher level protocols that don't care).
for ipv6 however, the checksum is not optional and receivers
would drop packets with a zero checksum.
during dhcp, ipconfig assigns the null address :: which makes
ipforme() return Runi for any destination, which can trigger
arp resolution when we attempt to reply. so have v4local()
skip the null address and have sendarp() check the return
status of v4local(), avoing the spurious arp requests.
closeconv() calls ipifcremmulti() like:
while((mp = cv->multi) != nil)
ipifcremmulti(cv, mp->ma, mp->ia);
so we have to defer freeing the entry after doing:
if((lifc = iplocalonifc(ifc, ia)) != nil)
remselfcache(f, ifc, lifc, ma);
which accesses the otherwise free'd ia and ma arguments.
on HZ 100 systems like pc and pc64, the minium sleep time
was 10ms, which is quite high. the cap isnt really needed
as arch specific timerset() enforces its own limit, but on
a higher resolution.
background:
from Charles Forsyth:
I haven't really got an opinion on it. The 10ms interval was first used on
machines that were much slower.
I thought someone did set HZ to a bigger value, partly to support better
in-kernel timing. I haven't done it because I never had a need for it.
If I were doing (say) protocol implementation in user mode, I'd certainly
reconsider. Sleep itself forces at best ms granularity,
and for some applications that's too big.
initial mail from qwx raising the issue:
> Hello,
>
> I found out recently that sleep(2)'s resolution on 386 and 9front's amd64
> kernel is 10 ms rather than 1 ms. The reason is that on those kernels,
> HZ is set to 100 rather than say 1000. In syssleep, we get 1 tich every
> 10 ms.
>
> What is unclear is why.
>
> To paraphrase cinap_lenrek's answer to my question:
>
> In syssleep:
> if(ms < TK2MS(1))
> ms = TK2MS(1);
> tsleep(&up->sleep, return0, 0, ms);
>
> "TK2MS(1)" can be replaced with just "1", and the arch specific
> timerset() routine would do its own capping of the period if it's too
> small for the timer resolution, and make better decisions based on what
> the minimum timer period should be given the latency overhead of the
> given arch's interrupt handling and performance characteristics.
>
> Alternatively, HZ could be raised to 500 or 1000.
>
> It seems it's just trying to prevent excessive context switches and
> interrupts, but it seems somewhat arbitrary. A ton of syscalls can be
> done in 1 ms, and it's the lowest we can go without changing the unit.
>
>
> What do you think?
>
> Thanks in advance,
>
> qwx
devdir internally replicates the qid in ther perm stat field
already and the practice of explicitely passing just causing
confusion when done inconsistently.
avoid returning ip addresses that cannot be reached due
to lack of a compatible ip address. this means when here
is no ipv4 address configured, we wont return ipv4 addresses
and would not query dns for an A record.
likewise, when here is no ipv6 address configured then
we wont query dns for an AAAA record.
ipv6 lookups can still be disabled with the -4 flag just
as before.
this makes virtual "memdisk" from SYSLINUX accessible to
the kernel, allowing the iso to be loaded via TFTP and
started without any ethernet or disk drivers available.
this driver makes regions of physical memory accessible as a disk.
to use it, ramdiskinit() has to be called before confinit(), so
that conf.mem[] banks can be reserved. currently, only pc and pc64
kernel use it, but otherwise the implementation is portable.
ramdisks are not zeroed when allocated, so that the contents are
preserved across warm reboots.
to not waste memory, physical segments do not allocate Page structures
or populate the segment pte's anymore. theres also a new SG_CHACHED
attribute.
fpurestore() unconditionally changed fpstate to FPinactive when
the kernel used the FPU. but in the FPinit case, the registers are
not saved by mathemu(), resulting in all zero initialized registers
being loaded once userspace uses the FPU so the process would have
wrong MXCR value.
the index overflow check was wrong with using shifted value.
due to linux omiting the final Z(4) in the NTLMv2 reply, and
the need for the windom for LMv2 authentication, here is a new
AuthNTLM ticket request now with length and dom fields.
in ntlmv2, the client will retry the challenge response trying a bunch
of different domain names assuming the same server challenge. so we have
to make retries work with factotum and the auth server.
also, windows 7 with compatlevel=4 sends all zeros LM response.
the dnsquery() library function should not start mouting /srv/dns on
its own. this problem arrises only for ndb/cs as it is started before
ndb/dns.
the issue with mounting /srv/dns before /net is when ndb/cs attempts
to read the list of interfaces, accessing /net/ipifc, which triggers
a rpc to ndb/dns as it is ontop of the mount. this can yield a deadlock
when ndb/dns blocks its 9p loop waiting for requests to complete on
a refresh and the requests are stuck waiting for ndb/cs to translate
a dial string for announce().
dblookup() used to only return the first matching entry. in
case of ipv6, we want all entries returned to get both v4
and v6 addresses... and these might not neccesarily be in
the same entry (see /lib/ndb/common). note also this makes
it behave the same as in cachedb mode which reads in the
whole database.
we do not know if v4 or v6 routing works, so the simplest
is just to query v4 and v6 nameservers in parallel. this is
done by changing serveraddrs() to return one address type,
and we make sure to get at least one v4 and one v6 address
each round.
get rid of the weigthed timeout code... there where too many
assumptions. instead, we give a round 500ms timeout (or 1 second
in patient mode) and honor the maximum query time.
we now update /net/ndb with the following information gathered
from router advertisements (rfc6106 and plan9 specific options):
- recursive dns servers (option 25, ndb: dns=)
- dns search list (option 31, ndb: dnsdomain=)
- plan9 fileserver (option 250, ndb: fs=)
- plan9 authserver (option 251, ndb: auth=)
note the plan9 specific options can be disabled with the -G flag.
for ndbconfig (-N flag), we now collect all ip addresses in ndb
belonging to the devices mac address and configue them all. v6
addresses are getting added when a link local address exists
or the -6 flag has been specified to automatically configure one.
move the dhcp code in its own dhcp.c file and make symbols static
that are not used across modules.
we have to maintain the ->line chain for ndbreorder() to work, so add
a little helper: ndbline() which replicates the ->entry chain and links
the last tuple to the first; makeing the whole list into a single line.
there appears to be confusion about the refresh flag of arpenter().
when we get an arp reply, it makes more sense to just refresh
waiting/existing entries instead creating a new one as we do not
know if we are going to communicate with the remote host in the future.
when we see an arp request for ourselfs however, we want to always
enter the senders address into the arp cache as it is likely the sender
attempts to communicate with us and with the arp entry, we can reply
immidiately.
reject senders from multicast/broadcast mac addresses. thats just silly.
we can get rid of the multicast/broadcast ip checks in ethermedium and
do it in arpenter() instead, checking the route type for the target to
see if its a non unicast target.
enforce strict separation of interface's arp entries by passing a
rlock'd ifc explicitely to arpenter, which we compare against the route
target interface. this makes sure arp/ndp replies only affect entries for
the receiving interface.
handle neighbor solicitation retransmission in nbsendsol() only. that is,
both ethermedium and the rxmitproc just call nbsendsol() which maintains
the timers and counters and handles the rotation on the re-transmission
chain.
no need to rlock ifc in targetttype() as we are called from icmpiput6(),
which the ifc rlocked.
for icmpadvise, the lport, destination *AND* source have to match.
a connection gets a packet when the packets destination matches the source
*OR* the packets source matches the destination.
v4lookup() and v6lookup() do not acquire the routelock, so it is
possible to hit routes that are on the freelist. to detect these,
we set ref to 0 and check for this case, avoiding overriding the ifc.
re-evaluate routes when the ifcid on the route hint doesnt match.
