the end condition port < offset+n could never become
false when offset truncated to 32 bit signed port is
negative. change the condition variables to unsigned
int.
msr's are not byte addressible, so advance reads by
one instead of 8.
nobody passes us the "RSD PTR " address when doing multiboot/kexec
on UEFI systems. so we search for it manually in the ACPI reserved
area as indicated in the e820 memory map.
this driver makes regions of physical memory accessible as a disk.
to use it, ramdiskinit() has to be called before confinit(), so
that conf.mem[] banks can be reserved. currently, only pc and pc64
kernel use it, but otherwise the implementation is portable.
ramdisks are not zeroed when allocated, so that the contents are
preserved across warm reboots.
to not waste memory, physical segments do not allocate Page structures
or populate the segment pte's anymore. theres also a new SG_CHACHED
attribute.
we allow devether to create ethernet cards on attach. this is useull
for virtual cards like the sink driver, so we can create a sink
by simply: bind -a '#l2:sink ea=112233445566' /net
the detach routine was never called, so remove it from the few drivers
that attempted to implement it.
the only architecture dependence of devether was enabling interrupts,
which is now done at the end of the driver's reset() function now.
the wifi stack and dummy ethersink also go to port/.
do the IRQ2->IRQ9 hack for pc kernels in intrenabale(), so not
every caller of intrenable() has to be aware of it.
the td index "x" was incremented twice, once in for loop
and in the body expression. so r->rp only got updated
every second completion. this is wrong, but harmless.
the driver doesnt implement multicast filter, but just turns
on promiscuous mode when a multicast address is added. but this
breaks when one actually enables and then disables promiscuous
mode with say, running snoopy.
we have to keep promisc mode active as long as multicast table
is not empty.
broadcast traffic was received back on the wire causing
duplicate address detection to break with dmat proy as
the rewritten broadcasts where observable.
the fix is to just ignore packets from ourselfs received
from the air. devether already handles loopback.
when kernel memory is exhausted, rtl8169replenish() can fail
to plant more receive descriptors and rtl8169receive() would
run over the receive tail and crash on the nil ctlr->rb[x].
rtl8169receive() is called on "Receive Descriptor Unavailable"
and "Packet Underrun" so we will try to replenish descriptors
in the beginning first in case memory was exhausted and memory
is available again and make sure not to run over the tail.
in case we continue to send traffic (like ping) with the ap gone,
the sending would keep updating bss->lastseen which prevents the
timeout to happen to switch bss.
- remove arbitrary limits on screen size, just check with badrect()
- post resize when physgscreenr is changed (actualsize ctl command)
- preserve physgscreenr across softscreen flag toggle
- honor panning flag on resize
- fix nil dereference in panning ctl command when scr->gscreen == nil
- use clipr when drawing vga plan 9 console (vgascreenwin())
to capture bios and bootloader messages, convert the contents
on the screen to kmesg.
on machines without legacy cga, the cga registers read out as
0xFF, resuting in out of bounds cgapos. so set cgapos to 0 in
that case.
new approach to graphics memory management:
the kernel driver never really cared about the size of stolen memory
directly. that was only to figure out the maximum allocation
to place the hardware cursor image somewhere at the end of the
allocation done by bios.
qu7uux's gm965 bios however wont steal enougth memory for his
native resolution so we have todo it manually.
the userspace igfx driver will figure out how much the bios
allocated by looking at the gtt only. then extend the memory by
creating a "fixed" physical segment.
the kernel driver allocates the memory for the cursor image
from normal kernel memory, and just maps it into the gtt at the
end of the virtual kernel framebuffer aperture.
thanks to qu7uux for the patch.
introducing the PFPU structue which allows the machine specific
code some flexibility on how to handle the FPU process state.
for example, in the pc and pc64 kernel, the FPsave structure is
arround 512 bytes. with avx512, it could grow up to 2K. instead
of embedding that into the Proc strucutre, it is more effective
to allocate it on first use of the fpu, as most processes do not
use simd or floating point in the first place. also, the FPsave
structure has special 16 byte alignment constraint, which further
favours dynamic allocation.
this gets rid of the memmoves in pc/pc64 kernels for the aligment.
there is also devproc, which is now checking if the fpsave area
is actually valid before reading it, avoiding debuggers to see
garbage data.
the Notsave structure is gone now, as it was not used on any
machine.
there isnt much of a point in keep maintaining separate
kernel configurations for terminal and cpu kernels as
the role can be switched with service=cpu boot parameter.
to make stuff cosistent, we will just have one "pc" kernel
and one "pc64" kernel configuration now.
we used to tweak arround in the ICH registers for all intel controllers,
which is wrong, as the 200 series has different magic registes. see
the datasheet:
https://www.intel.com/content/www/us/en/chipsets/200-series-chipset-pch-datasheet-vol-2.html
this caused the clocks to be disabled for the 6th port causing a full
machine lockup touching the 6th port registers.
the next problem was that aiju's bios disabled the unused ports somehow
but didnt clear ther PI bits, so that they would stay in Sbist status even
after a port reset. so the port would get stuck in the Dportreset state
forever. the fix for this was to use a one second timeout for the
port reset procedure.
more conservative approach: only one transaction in flight
per endpoint (except iso). also serialize controller commands.
no driver currently uses this and i doubt it is usefull.
create constants for common TRB flags and remove bogus 1<<16
flag on TR_NORMAL.
while endpoints != 0 are opend after the device descriptor has been
parsed and the endpoint properties like maxpkt have been set, the
control endpoint is opend with a guessed maxpkt value. once the first
8 bytes of the descriptor have been read by usbd, maxpkt gets set and
we need to reevaluate the control endpoint 0 context to update the value.
instead of guessing where the controllers dequeue pointer went,
stop the endpoint and then explicitely set te dequeue pointer to
the next write td position. that way we do not need to fix the cycle
bit in the td's and dont need to rely on if the controller
advanced the dequeue pointer after a stall or not.
add ctx and slot back pointers to ring.
add support for edp, dp and hdmi on haswell and haswell ult.
vga, dvi and specific configurations like ulx are unimplemented.
remaining issue: edp link training always fails (time out).
turns out on real hardware, the front falls off if we write
the completion queue doorbell registers without consuming
an entry. so only write the register when we have processed
something.
basic NVMe controller driver, reads and writes work.
"namespaces" show up as logical units.
uses pin/msi interrupts (no msi-x support yet).
one submission queue per cpu, shared completion queue.
no recovery from fatal controller errors.
only tested in qemu (no hardware available).
commiting this so it can be found by someone who has
hardware.
on thinkpad x1v4, the PCMP structure resides in upper reserved memory
pa=0xd7f49000 - while system memory ends at 0x0ffff000; so we have to
vmap() it instead of KADDR().
the RSD structure for ACPI might reside in low memory, so we sould
KADDR() in that case.
devmouse controls the screen blanking timeout, so move the
code there avoiding cross calls between modules. the only
function that needs to be provided is blankscreen(), which
gets called with drawlock locked.
the blank timeout is set thru /dev/mousectl now, so kernels
without devvga can set it.
blanking now only happens while /dev/mouse is read. so this
avoids accidentally blanking the screen on cpu servers that
do not have a mouse to unblank it.
- add some milisecond timestamps to the status change debug printing
- flush the packets in the queue on deassoc to avoid processing old pae
packets on next association.
- make roaming timeout shorter (60 -> 20 seconds)
- automatically timeout and restart wpa/pae blocked state
- fix printing race when essid gets changed underneath seprint
from openbsd driver, it seems the Centrino Advanced-N 6030 and 6235
cards share the same device revision as the 6205 (Type6005). Also
changing the device revision field from 4 to 5 bits.
- drivers enable short preamble and sort timeslot depending
on the ap beacon capinfo field (bss->cap)
- wifi sets short preamble bit in capinfo on association request
- wifi sets short timeslot bit when ap advertized it in beacon
given that the igfx driver doesnt provide any acceleration functions
and drawing is usually faster with double buffering as it eleminates
reads over the pci bus, enable softscreen by default.
on 386 kernel, each processor has its own pdb where the primary
pdb for kernel mappings is on cpu0 and other cpu's lazily pull
pdb entries from cpu0 when they fault in vmapsync().
so we have to edit the table tables in the pdb of cpu0 and not
the current processor.
on some modern machines like the x250, the bios arranges the mtrr's
and the framebuffer membar in a way that doesnt allow us to mark
the framebuffer pages as write combining, leading to slow graphics.
since the pentium III, the processor interprets the page table bit
combinations of the WT, CD and bit7 bits as an index into the
page attribute table (PAT).
to not change the semantics of the WT and CD bits, we preserve
the bit patterns 0-3 and use the last entry 7 for write combining.
(done in mmuinit() for each core).
the new patwc() function takes virtual address range and changes
the page table marking the range as write combining. no attempt
is made on invalidating tlb's. doesnt matter in our case as the
following mtrr() call in screen.c does it for us.
get rid of _INI and _REG method calls, this is not full acpi environment
anyway and all we really want todo at kernel boot time is figuring out
the interrupt routing. aux/acpi can try to enable more stuff if it needs
to later when battery status desired.
dont snoop memory space regions in amlmapio(), this is just wrong as
amlmapio() is *lazily* mapping regions as they are accessed, so the
range table would never be really complete. instead, we provide generic
access to the physical address space, excluding kernel and user memory
with acpimem file.
the first time rtl8169link is called (from rtl8169pnp), the link isn't up, so
setting edev->mbps based on Phystatus register is skipped. edev->mbps is then
still set at the default 100, and that ends up being what devether uses.
this is why some rtl8169 cards are misprinted as 100Mbps in kmesg.
later, after rtl8169link is called again from rtl8169interrupt, the link is up
and edev->mbps is set to the correct value (as shown by e.g. /net/ether0/stats).
so instead, set speed regardless of link status.
