This avoids ipconfig having to explicitely specify the tag
when we want to set route type, as the tag can be provided
implicitely thru the "tag" command.
This adds a new route "t"-flag that enables network address translation,
replacing the source address (and local port) of a forwarded packet to
one of the outgoing interface.
The state for a translation is kept in a new Translation structure,
which contains two Iphash entries, so it can be inserted into the
per protocol 4-tuple hash table, requiering no extra lookups.
Translations have a low overhead (~200 bytes on amd64),
so we can have many of them. They get reused after 5 minutes
of inactivity or when the per protocol limit of 1000 entries
is reached (then the one with longest inactivity is reused).
The protocol needs to export a "forward" function that is responsible
for modifying the forwarded packet, and then handle translations in
its input function for iphash hits with Iphash.trans != 0.
This patch also fixes a few minor things found during development:
- Include the Iphash in the Conv structure, avoiding estra malloc
- Fix ttl exceeded check (ttl < 1 -> ttl <= 1)
- Router should not reply with ttl exceeded for multicast flows
- Extra checks for icmp advice to avoid protocol confusions.
The altsetting was handled only for a single endpoint
(per interface number), but has to be handled for each
endpoint (per interface *AND* altsetting number).
A multi function device (like a disk) can have
multiple interfaces, all with the same interface number
but varying altsetting numbers and each of these
interfaces would list distict endpoint configurations.
Multiple interfaces can even share some endpoints (they
use the same endpoint addresses), but
we still have to duplicate them for each
interface+altsetting number (as they'r part of
actually distict interfaces with distict endpoint
configurations).
It is also important to *NOT* make endpoints bi-directional
(dir == Eboth) when only one direction is used in a
interface/altsetting and the other direction in another.
This was the case for nusb/disk with some seagate drive
where endpoints where shared between the UAS and
usb storage class interface (but with distict altsettings).
The duplicate endpoints (as in using the same endpoint address)
are chained together by a next pointer and the head
is stored in Usbdev.ep[addr], where addr is the endpoint
address. These Ep structures will have distinct endpoint
numbers Ep.id (when they have conflicting types), but all
will share the endpoint address (lower 4 bits of the
endpoint number).
The consequence is that all of the endpoints configuration
(attributes, interval) is now stored in the Ep struct and
no more Altc struct is present.
A pointer to the Ep struct has to be passed to openep()
for it to configure the endpoint.
For the Iface struct, we will now create multiple of them:
one for each interface *AND* altsetting nunber,
chained together on a next pointer and the head being
stored in conf->iface[ifaceid].
--
cinap
Some gba cartridges use flash chips produced by a few different
manufacturers for backup memory. A game rom may then try to read the
device id for its flash chip and break if it's the wrong one. There's
no way for us to know which chip is supposed to be there, save for
looking it up in some database. These chips are either 64k or 128k
big. gba(1) hardcodes the id for the SST 64k chip, but games like the
Pokémon ones use a 128k Macronix chip and expect a different id,
completely breaking them.
This patch sets a different default for 128k flash backups, and gives
the ability to set the exact type when creating the save file if it's
really necessary. This new default fixes the Pokémons. The type is
saved in the save file, but this will *not* break existing ones. It
may be that we don't need to worry about the type and just have an id
that corresponds to the right chip size, which is why these defaults
make sense, but I haven't tested more than a dozen roms, mostly since
I don't really know which games use 128k flash.
This allows mapping incoming filenames to a different name
using regular expressions, followed by subtitutions
of the %[ICE] format strings.
I needed this to have individual cmdline.txt files for
netbooted raspberry pi's. In this example, i map cmdline.txt
to %C, which gets substituted for /cfg/pxe/$ether of the client.
Sometimes, there is the one-off occation when one needs to
pass a huge list in rc...
This change makes devenv track total memory consumption
of environment groups allowing them to grow up to 1MB in
size (including overhead).
(Before, only the variable size was restricted, but
not the amount of files being created).
The maximum value size of a single environment variable
is set to half of the total size, which allows the
occational large value. (But not many of them).
Because we track all memory consuption, it is also
now possible to create around 10k small environment
variales.
A hashtable is added for name lookups and the qid.path
was changed to allow direct indexing into the entry
array without needing a scan lookup.
All smalloc() calls have been removed, exhaustion is
handled with error(Enomem) avoiding deadlock
in case we run out of kernel memory.
Untangle the lexer and interpreter thread state.
Fix the file and line number error reporting, getting rid of
Xsrcfile instruction, as the whole code block can only come
from a single file, stuff the source file in slot[1] of the
code block instead.
Remove limitations for globber (path element limits)
and be more intelligent about handling globbing by
inserting Xglob instruction only when needed and not
run it over every Xsimple argument list.
Remove fragile ndot magic and make it explicit by adding
the -q flag to . builtin command.
Add -b flag for full compilation.
Make exitnext() smart, so we can speculate thru rcmain and
avoid the fork().
Get rid of all print(2) format functions and use io
instead.
Improve the io library, adding rstr() to handle tokenization,
which allows us to look ahead in the already read buffer
for the terminators, avoiding alot of string copies.
Auto indent pcmd(), to make line number reporting more usefull.
Implement here documents properly, so they can work everywhere.
SSL is implemented by devssl. It's extremely
obsolete by now, and is not used anywhere but
cpu, import, and oexportfs.
This change strips out the devssl bits, but
does not (yet) remove the code from libsec.
g(1): sync filetypes list
the file types list in the 'g' manual was out of date.
this change synchronizes and sorts them.
it looks like the .B macro only accepts 6 args or less,
so observe that limit.
