this was a big mistake. we should never attempt to
timeout or retry a scsi command from the controller
driver because theres no way to tell how long a
command would take or if a command has side effects
when being retried.
ftrvxmtrx repots devices that use the endpoint number for
input and output of different types like:
nusb/ether: parsedesc endpoint 5[7] 07 05 81 03 08 00 09 # ep1 in intr
nusb/ether: parsedesc endpoint 5[7] 07 05 82 02 00 02 00
nusb/ether: parsedesc endpoint 5[7] 07 05 01 02 00 02 00 # ep1 out bulk
the previous change tried to work arround this but had the
concequence that only the lastly defined endpoint was
usable.
this change addresses the issue by allowing up to 32 endpoints
per device (16 output + 16 input endpoints) in devusb. the
hci driver will ignore the 4th bit and will only use the
lower 4 bits as endpoint address when talking to the usb
device.
when we encounter a conflict, we map the input endpoint
to the upper id range 16..31 and the output endpoint
to id 0..15 so two distinct endpoints are created.
the 802.11 spec only specifies the msb of the rate for
Beacon, Probe Response, Association Response, Reassociation Response,
Mesh Peering Open, and Mesh Peering Confirm management frames
...
The MSB of each Supported Rate octet in other
management frame types is ignored by receiving STAs.
this should make no difference but on some netgear ap's not
setting this bit seems to ignore these data rates.
driver sets wifi->rates array to tell wifi layer what
rates it supports. when we receive beacon, we determine
the minimum and maximum data rates and set wn->minrate
and wn->maxrate to point to the entries in wifi->rates.
it is the responsibility of the driver to use this
information on transmit.
according to erik, virtualbox puts the source overrides
before the ioapic entries so the addirq() call fails
as no ioapics have been declared yet. use a second pass
over the table after we processed the apic entries.
do not store Block* pointer in packet descriptor, assumed
pointer would fit in a long. we use pointer table now to
record the Block* pointer and store index instead.
this change is in preparation for amd64. the systab calling
convention was also changed to return uintptr (as segattach
returns a pointer) and the arguments are now passed as
va_list which handles amd64 arguments properly (all arguments
are passed in 64bit quantities on the stack, tho the upper
part will not be initialized when the element is smaller
than 8 bytes).
this is partial. xalloc needs to be converted in the future.
according to a comment in linux driver, reading Isrc2
register caused interrupts to be disabled. we used
to read Isrc2 in ifstat() and it was confirmed that
reading ifstat locks up ethernet. removing the Isrc2
read in ifstats, and also reenable interrupts after
reading Isrc2 when the interrupt was not for us.
(this is from the linux driver)
in replenish(), set ring software write pointer (Sring.wp)
*before* the hardware write index register. otherwise
rx() could get status notification for completed
receive but wont find the rx descriptor in the ring.
handle uint wrap arround when calculating ring fill
count and remaining count.
disabling mouse packet streaming command 0xf5 can fail
when a packet is currently transmitted.
this can be seen when one moves the mouse while running:
while(){echo accelerated >/dev/mousectl; sleep 0.5}
dont spam the console with qfull warnings. this makes things worse.
handle loopback packets as stated in the comment. we call etheriq()
with fromwire=1 for loopback packets so etheriq() can pass the packet
on (without copying) or free it. dont inhibit interrupts while calling
etheriq(). etheriq() can safely be called from process and interrupt
context. it is unclear what this was supposed to fix and testing didnt
seem to have any odd effects.
catch the error() that can be thrown by sleep() and tsleep()
in kprocs.
add missing pexit() calls.
always set the freemem argument to pexit() from kproc otherwise
the process gets added to the broken list.
the diver used to skip auto negotiation when
auto-negotiation enable (bit 12 in command register)
was clear.
setting the bit now, which makes auto negotiation work.
we skip auto negotiation only when it was already enabled
and status regiser indicates completion (bit 9).
