Add two mechanism for avoiding name-collisions in a system-wide
installation of charybdis. The ssld and bandb daemons, intended to be
directly used by ircd and not the user, install into libexec when
--enable-fhs-paths is set. For binaries which are meant to be in PATH
(bindir), such as ircd and viconf, there is now an option
--with-program-prefix=progprefix inspired by automake. If the user
specifies --with-program-prefix=charybdis, the ircd binary is named
charybdisircd when installed.
Add support for saving the pidfile to a rundir and storing the ban
database in localstatedir instead of in sysconfdir. This is, again,
conditional on --enable-fhs-paths.
Fix(?) genssl.sh to always write created SSL key/certificate/dh
parameters to the sysconfdir specified during ./configure. The
previous behavior was to assume that the user ran genssl.sh after
ensuring that his current working directory was either sysconfdir or a
sibling directory of sysconfdir.
This becomes important because of away-notify sending aways to common
channels much like nick changes (which are also paced).
Marking as unaway is not limited (but obviously only does something if the
user was away before). To allow users to fix typos in away messages, two
aways are allowed in sequence if away has not been used recently.
This makes accounting of number of bits allocated easier. Specifically, the amount of allocated
bits is computed by doing (index->highest_bit - 1) in code.
Specifically, what this capability manager does, is map keywords to
calculated bitmasks. These bitmasks are allocated at runtime, so that
the any managed capability index can be manipulated by modules.
Modules should call capability_orphan() when orphaning capabilities. This
makes it so that bitmasks aren't reallocated, except for cases where the
capability is the same.
This adds a new ISUPPORT token, NICKLEN_USABLE which is strictly an informative value.
NICKLEN is always the maximum runtime NICKLEN supported by the IRCd, as other servers may
have their own usable NICKLEN settings. As NICKLEN_USABLE is strictly informative, and
NICKLEN is always the maximum possible NICKLEN, any clients which depend on NICKLEN for
memory preallocation will be unaffected by runtime changes to NICKLEN_USABLE.
The default NICKLEN is 50; the default serverinfo::nicklen in the config file is set to
30, which is the NICKLEN presently used on StaticBox.
This used to be only advertised if a service was linked, which made
sense in ratbox when +r was only settable if services were available.
Now, however, +r is always available and so should always be advertised.
After a configuration change (or deoper with no_oper_flood) sent_parsed
might be way higher than allow_read, so that the user would have to wait
a long time before the server responds. Avoid this.
They are now in messages, even if client_flood_message_time is not 1.
If client_flood_message_time is not 1 (by default it is), this needs a
configuration change to maintain the same behaviour.
* Deduce allow_read from the client's state (IsFloodDone) rather than
storing it in LocalUser.
* Fix the documentation (in oper /info), however strange
client_flood_burst_rate and client_flood_burst_max may seem, that is
how they currently work.
After setting up signal handlers, unmask the signals we care about
(installed handlers for).
When handling SIGINT, the kernel adds SIGHUP and SIGINT to the signal
mask (as requested in sigaction()); if execve() is called from the
signal handler, this change is persistent.
nenolod gave the thumbs-up to port ircd-seven banfowards to charybdis to spb
for a while, and people have asked about it. Might as well do it since it's a
slow weekend.
Note that as a side effect use_forward is removed from the config and
unconditionally enabled!
While what chanroles are trying to accomplish is a good idea, it is
apparently unclear this is the proper way to do it. Until we figure out
the exact way we wish to do this, it should be reverted for now.
The theory behind this is that services sends an ENCAP * GRANT #channel
UID :+flagspec message specifying the chanroles the user has. They are
mapped into flag bits and applied to the membership of the user. They
then are restricted or permitted to what they can do based on the
permissions mask regardless of rank.
For backwards compatibility, the default permission bit (without a GRANT
statement) allows a user to to anything an existing op can do ONLY if
they are an op.
Todo: make CHANROLE_STATUS work (the ability to apply +ov to people),
which is at the moment controlled by CHANROLE_MODE.
yy_oper->certfp was not copied into yy_tmpoper->certfp, thus the information was lost and certfp auth was never really working, since the string was always empty.
Any hunted parameter with wildcards is now assumed
to be a server, never a user.
Reasons:
* fewer match() calls
* do not disclose existing nicknames
* more intuitive behaviour for CONNECT
m_trace has a copy of some hunt_server logic in it
(for the RPL_TRACELINK reply), so adjust that too.
Do not allow a user to op themselves if they are
already opped, as "already opped" could be because
of OMODE's hack which will be unconditionally
reverted after the mode change.
Also, this matches old behaviour for users not
being able to generate mode changes redundantly
opping themselves.
Note that this change should only be taken advantage
of if all servers run patched code. Otherwise, mode
changes will be silently dropped and a desync
results.
The extended-join client capability extends the JOIN message with information clients typically
query using WHO including accountname, signon TS and realname.
These seem unnecessary and may cause problems because they
are wrong in some cases.
A comment says these were needed for GCC 3.3. If you are
still using this compiler, check this and if it breaks,
some other approach is needed.
