- Use the same lock in the IUSBQueue as in the IDMAMemoryManager
- add debug traces (default off)
svn path=/branches/usb-bringup-trunk/; revision=55110
- Add usbd to bootcd because usbohci depends on it
- Make device interface creation failure a non-fatal error so the port drivers start successfully in 1st stage
svn path=/branches/usb-bringup-trunk/; revision=55034
- When clearing feature port reset, remove the flag from Change and if the port is hardware enabled set the enable flag in Status.
- When checking port status, if Change has any flags set an SCE request most be completed. Verified while writing usbhub driver in xp.
- Probably fixes a case where an endless loop of completing SCE requests.
svn path=/branches/usb-bringup/; revision=51642
- Invoke status change callback at passive level
- Fill out usb descriptor struct instead passing everything in char array
- Use 1 byte interrupt endpoint packet size for hub for now
- Fill in interface information when SelectConfiguration request is passed. Fixes sce callback and pool corruptions
- Return device descriptor in USBHI_QueryDeviceInformation
- Tested in WinXP with special pool enabled & overrun support
svn path=/branches/usb-bringup/; revision=51572
- Port URB_FUNCTION_CLASS_INTERFACE from mjmartin usbehci driver
- Fix typo in interface declaration
- Disable assert for now
- Return irp status pending when irp is added to the queue
- Fix bug in InternalGetPidDirection
- More work on the bulk transfers, not yet working
svn path=/branches/usb-bringup/; revision=51501
- Fix a type causing CommitIrp to fail.
- Add a sanity check in StatusChangeEndpointCallBack to check that a pending SCE irp is queued.
- Start Implementing Bulk Transfers. Needs more work.
svn path=/branches/usb-bringup/; revision=51493
- hub_controller.cpp: Change RtlSetBit and RtlClearBit to RtlSetBtis and RtlClearBits for Win2k compatibility.
svn path=/branches/usb-bringup/; revision=51488
- Implement retrieving device / configuration descriptor for usb devices
- Based on mjmartin usbehci driver
- Mass storage device found wizard now pops up (fails to install - WIP)
svn path=/branches/usb-bringup/; revision=51478
- Cache port status & port change settings because it appears that some ehci controllers do not store the status reset register bit correctly
- This commit is a temporary solutions, needs to be reworked
- Return correct status from HandleClassOther
- Handle IOCTL_INTERNAL_USB_SUBMIT_IDLE_NOTIFICATION to return status success
svn path=/branches/usb-bringup/; revision=51473
- Return the physical address of the async queue head in CUSBHardwareDevice::GetAsyncListRegister
- Remove superflous entries from queue head structure, they are processed within IUSBRequest class
- Remove USBHI_GetPortHackFlags, this function has been deprecated
- Add interface functions for IUSBRequest / IUSBQueue
- Callback into IUSBQueue when a hardware interrupt arrives
- Implement callback function to check for completed queue heads / free completed queue head depending on the Async Advance interrupt bit
svn path=/branches/usb-bringup/; revision=51466
hub_controller:
- Implement StatusChangeEndpointCallBack called by HardwareDevice class when port status has changed on controller.
- Move Status Change Endpoint query code to IQueryStatusChageEndpoint as it is also needed by StatusChangeEndpointCallBack.
usb_request:
- Implement InternalCreateUsbRequest.
usb_queue:
- Implement CreateUsbRequest and AddUsbRequest
hardware:
- Implement GetAsyncListRegister and GetPeriodicListRegister.
- Implement SetStatusChangeEndpointCallBack for setting callback and context. Call the callback when a port status changes.
- Initialize the UsbQueue after creating the AsyncQueueHead, as the UsbQueue calls will call back with GetAsyncListRegister.
svn path=/branches/usb-bringup/; revision=51407
- Fix warning because comparing signed vs unsigned
- Implement function for retrieving the device descriptor
- Implement function for retrieving a configuration descriptor (including contained interface descriptor and endpoint descriptor)
- Cleanup interface for IUSBRequest:
- When caller initializes IUSBRequest with an IRP, then the operation mode is asynchronously. Therefore when the request is completed, IUSBRequest::ShouldReleaseRequestAfterCompletion will return true, which makes IUSBQueue call Release on IUSBRequest
- When the caller initializes IUSBRequest with an setup packet, the operation mode is synchronously. After submitting the IUSBRequest to queue, the caller should call IUSBRequest::GetResultStatus. This function will then block untill the operation has been completed. However, the caller needs to call Release() as those requests are not cleaned up by the IUSBQueue
svn path=/branches/usb-bringup/; revision=51406
- hub_controller: Implement Status Change Endpoint for RootHub.
Handling the URB can return STATUS_PENDING, as in the new SCE code. Check for this before completing the Irp.
Uncomment calls to PortStatus, SetPortFeature, and ClearPortStatus now that they are implemented.
- For function receiving a port number check that its not larger than the actual number of ports on the controller.
svn path=/branches/usb-bringup/; revision=51401
- Move USB_REQUEST_SET_FEATURE / USB_REQUEST_GET_FEATURE flags to header file.
- Remove QueueHead and Descriptor creation as its in UsbRequest.
- Move DMACommon Buffer allocation back to UsbHardwareDevice class.
- Implement Port Handling functions GetPortStatus, ClearPortStatus and SetPortFeature.
- Implement GetUSBQueue for returning pointer to UsbQueue and GetDMA to return DMAMemoryManager.
- Fix a typo in one of the defines for Port Register Flags.
svn path=/branches/usb-bringup/; revision=51397
- Implement IRP_MN_QUERY_DEVICE_RELATIONS for hub controller object
- Implement stub handler for URB_FUNCTION_CLASS_OTHER, URB_FUNCTION_SELECT_CONFIGURATION
- Partly implement URB_FUNCTION_GET_STATUS_FROM_DEVICE
- Return success from unimplemented USBHI_Initialize20Hub routine
- based on mjmartin usbehci driver
- Tested in Windows XP SP2
svn path=/branches/usb-bringup/; revision=51385
- Setup a default device descriptor for the root hub and initialize it with vendor & product id
- Partly implement URB_FUNCTION_GET_DESCRIPTOR_FROM_DEVICE, URB_FUNCTION_CLASS_DEVICE
- based on mjmartin usbehci
svn path=/branches/usb-bringup/; revision=51384
- Fix bug in CDMAMemoryManager initialization, which calculated the bitmap length wrong
- Create interface IUSBDevice, which will be used to abstract connected usb devices
- Implement support functions for the device interface.
- Implement USBHI_CreateUsbDevice, USBHI_InitializeUsbDevice, USBHI_GetUsbDescriptors, USBHI_RemoveUsbDevice, USBHI_GetExtendedHubInformation, USBHI_RootHubInitNotification, USBHI_SetDeviceHandleData, USBDI_GetUSBDIVersion, USBDI_IsDeviceHighSpeed
- Partly implement USBHI_QueryDeviceInformation
- Based on mjmartin usbehci
svn path=/branches/usb-bringup/; revision=51372
- Add reference count when the hub controller is created. Necessary to prevent the controller from getting deleted when the hub driver performs interface reference removes
- Implement IRP_MN_QUERY_ID, based on mjmartin ehci driver
- Fix bug in IRP_MN_QUERY_BUS_INFORMATION, it is supposed to return a PNP_BUS_INFORMATION not a simple guid
- Implement IOCTL_INTERNAL_USB_GET_DEVICE_HANDLE, IOCTL_INTERNAL_USB_GET_ROOTHUB_PDO, IOCTL_INTERNAL_USB_GET_HUB_COUNT based on mjmartin ehci driver
- Add interfaces for communicating with the hub driver
- Dispatch internal device requests not wmi requests (EHCI_Dispatch)
svn path=/branches/usb-bringup/; revision=51368
- Create Interface IDispatchIrp which is used to handle ioctl requests
- Partly implement IHubController interface
svn path=/branches/usb-bringup/; revision=51355